Pre-Roast vs Post-Roast Blending: How Roasters Build a Coffee Blend
Every house blend starts with one workflow decision. Do you mix the green coffee and roast it together, or roast each coffee alone and combine them afterward? That choice is...
Scorched faces, burnt tips or a flat, bready cup can show up the first week you run a roaster you didn't buy new. Most guides to roast defects blame the profile and tell you to change your charge temperature. On a used roaster, that is only half the picture. The machine's setup, condition and cleanliness shape every batch too, and those causes are usually simple to find and fix.
This guide shows you how to identify each defect, then check the machine first and the profile second. It's written for buyers who just installed a pre-owned drum roaster. It's also for owners who want a clear checking order before they rewrite a profile that used to work.
When a used roaster produces defects, check the machine before the profile. Confirm the batch fits the drum, the drum turns at the right speed, airflow is clear, and the thermocouples read true. Then adjust charge temperature, early heat and the late rate of rise.
Why this order? Profile changes are cheap to try, so most roasters start there. On a machine you just inherited, though, the profile often isn't the problem. You can lower your charge temperature five batches in a row and still see scorching. The real cause might be a slow drum or an exhaust half blocked with chaff. Fix the machine, and the profile you already know usually starts working again.
Roast defects fall into two groups. Objective defects leave marks you can see on the bean. Subjective defects show up in the cup and depend partly on who is tasting. Loring's technical paper on avoiding roasting defects uses the same split and is good further reading.
Small dark brown or black specks on the flat face of the bean, usually visible before the coffee has turned tan. Scorching comes from beans sitting against metal that is too hot. In the cup it reads as smoky, ashy and bitter.
Dark marks on the ends of the bean, where the germ sits. That end is weaker than the rest of the seed, so it burns first when heat arrives too fast. Dense, high-grown coffee tends to hold up better than soft, low-density coffee.
Facing looks like scorching but shows up late in the roast. As beans expand, they press harder against the drum wall, and an overheated drum marks the flat side. A batch that is too big for the drum makes facing more likely.
Baked coffee looks normal. It tastes flat, dull, bready or papery, without the sweetness the green coffee should have. Roasters still debate the exact cause. The most common explanation is a rate of rise that stalls or dips late in the roast, often before or right after first crack.

A batch with light and dark beans mixed together, or beans that look done outside but taste grassy and sour inside. This is where green coffee matters too. Mixed screen sizes, moisture or density roast unevenly on any machine. It helps to know how to grade green coffee before you blame the roaster. In a blend roasted together, coffees with different densities color at different rates. That's one reason roasters weigh pre-roast vs post-roast blending.
Two roasters of the same make and model rarely behave the same way. A used machine adds its own history on top of that. Here is what usually changes when a roaster moves from one roastery to another:
None of this means a used roaster is a compromise. It means commissioning matters. Our guide to commissioning a used roaster covers the first heat-up, seasoning and dialing in. The checks below pick up where that guide ends, once defects start showing up in real batches.
Run these in order. The first three take minutes and cover most cases. Write down what you find, even when everything looks fine. That record becomes your baseline.

Check the data plate for the rated batch size and weigh your green coffee. An overfilled drum restricts bean movement and airflow, which leads to scorching and facing. A batch far too small for the drum leaves the bean probe uncovered and lets beans spend more time against hot metal. If you moved up from a smaller roaster, start near the middle of the machine's range.
Count the drum's rotations for one full minute and compare the number to the manufacturer's spec. Roasting consultant Scott Rao covers this in his post on tuning your roasting machine. He notes that drum speed can vary noticeably between identical models. A drum running too fast or too slow increases conductive heat damage. Listen for slipping belts or chains, and check that the motor holds speed under load. A drum that turns too slowly lets beans rest on hot metal, which is a classic scorching cause.
Airflow carries heat into the bean pile and carries smoke and chaff out. Low airflow raises scorching risk and leaves smoky notes in the cup. Check that the exhaust fan spins the right way, the damper moves through its full range, and the ducting has no leaks. Does your roaster have a manometer or a fan driven by a variable frequency drive (VFD)? Record the reading so you can compare it batch to batch. Heavy smoke or loose chaff at drop on a light roast is a sign of low airflow. Your roast curve gives clues too. Scott Rao notes that an environment temperature that peaks well before first crack can point to too much airflow, while one still climbing at the end of the roast can point to too little.
Chaff in the cyclone, the chaff collector or the ducting chokes airflow over time. Coffee oil baked onto the drum and the cooling tray changes how heat moves and can add stale, burnt flavors. If defects crept in gradually on a machine that used to roast well, buildup is the first suspect. Our guide on how to clean and maintain a used drum roaster has the full daily, weekly and monthly routine.
Look at the flame through the sight glass with the burner lit. You want an even, blue flame across the whole burner. Yellow tips, a lifting flame or dead spots point to clogged ports, the wrong supply pressure or an incomplete fuel conversion. Uneven flame means uneven drum heat, which shows up as hot spots, scorching and patchy color. Observe and note it, then hand any adjustment to a qualified gas technician.
Your bean temperature (BT) and environment temperature (ET) probes drive every decision you make. Check that both are seated, undamaged and in the position the manufacturer specifies. The bean probe needs to sit in the bean pile, not in open air. Compare each probe against a reference thermometer. A probe that reads low tells you to add heat the coffee doesn't need, which can look exactly like a profile problem. A slow probe shows up on the curve as well. If your turning point routinely lands late, the probe may be responding too slowly to track the roast. Thermocouple replacement is a technician job.
Drum design changes how much each check matters. Conventional drum roasters such as Probat and Diedrich heat the beans through a mix of hot drum steel and hot air. On these machines, drum speed and burner condition matter a lot. Loring roasters heat the beans mainly with hot air. Loring's paper argues that this convection design largely prevents scorching and facing. If you are comparing machines, our used Loring roasters collection covers models from the S7 Nighthawk up to the S70 Peregrine. Whatever the design, the six checks above still apply.
Once the machine checks out, look at the profile. These are the levers that most often cause each defect.
Two roasters will often disagree on whether a cup is baked. Cup side by side, ideally with a second taster, before you make a big change.
Find the row that matches your batch, then work left to right: machine checks first, profile fix second.
| Defect | What you see or taste | Machine checks first | Profile fixes |
|---|---|---|---|
| Scorching | Dark specks on the flat face early in the roast; smoky, ashy cup | Drum speed, batch size, airflow, uneven flame | Lower charge temperature; less heat in early drying |
| Tipping | Burnt ends of the bean; sharp roasty notes | Thermocouple readings, flame condition, airflow | Gentler early heat; slower roast for soft, low-density coffee |
| Facing | Dark patches on the flat side late in the roast | Batch size against rated capacity, drum speed | Less heat approaching first crack; smaller batch |
| Baking | Normal look; flat, bready or papery cup | Bean probe placement, gas supply pressure, airflow | Keep RoR declining smoothly; avoid a late stall or crash |
| Uneven color | Light and dark beans mixed in one batch | Drum speed, overfilled drum, chaff buildup, flame | Check green coffee grading; roast blend components separately |
| Underdevelopment | Grassy, sour, peanut-like cup; beans may look done | Thermocouple calibration, low gas pressure | Extend development; carry more energy into first crack |
A roast log is the fastest way to separate machine problems from profile problems. When the curve looks the same as last month but the cup doesn't, look at the machine. When the curve changed, start with the profile.
Log these for every batch: coffee and lot, batch weight, charge temperature, gas and airflow changes, turning point, first crack, drop, development time and weight loss. Add a roast color reading after cooling. Our guide to the Agtron scale explains how color numbers work, and why they need to be read alongside the cup. Print the log sheet below and keep it by the roaster, so every batch and every machine check lands in one place.

Software makes this far easier. Artisan and Cropster both draw your BT, ET and RoR live and save each batch for comparison. Roughly 4 in 10 roasters listed on CoffeeTec mention Cropster, Artisan, a data port or thermocouple logging in the listing. If yours came with one, ask the seller for their saved profiles. Our guide to coffee roasting software and roast profiling covers setup and how to read the curves.
Most defect hunting is safe and simple: weighing batches, counting drum turns, cleaning ducts and comparing probes. Some findings belong with a professional. Call a qualified technician when you see:
Keep every service visit in your log. A documented fix protects your roast quality today and your resale value later.
On calls with buyers, the CoffeeTec team points to the same places these checks cover. Venting comes up first: the pipe from the roaster to the chaff collector often ships with the machine, but the run up through your ceiling or wall usually doesn't, so plan that with your installer. If a roaster moves to a different gas, the burner needs the right orifice for it. And ask the seller, through CoffeeTec, how often they cleaned the machine and whether it logs to Cropster or Artisan.
If you are shopping, ask how the roaster was installed, how it was vented, and when the probes were last calibrated. Ask for a recent roast log or saved profiles. Those answers tell you how much setup work to plan for. Our guide on how to buy a used coffee roaster covers the full pre-purchase process.
Own a roaster that no longer fits your volume or style? CoffeeTec can help you sell it and move into a better fit through a roaster refresh. A machine with clean ducts, calibrated probes and a written service log is easier to sell. The next owner can also dial it in faster. When you're ready, list your used roasting equipment with CoffeeTec and include your roast logs and service records with the photos.
Yes. Chaff in the ducting or cyclone restricts airflow, which raises the risk of scorching and smoky flavors. Oil baked onto the drum and cooling tray can add stale, burnt notes. If defects appeared gradually on a machine that used to roast well, clean it before you change the profile.
Yes. A drum that turns too slowly lets beans rest against hot metal, which causes scorching. A drum that turns too fast can pin beans to the wall. Count rotations for one minute and compare the number to the manufacturer's spec before you adjust anything else.
Often, but not always. Check that your thermocouples read true and that the flame is even first. If the probes read low, you may already be charging hotter than you think. Once the machine checks out, lower the charge in small steps and soften early heat.
Both views exist. Baked coffee has no visible marks, so it is judged in the cup, and tasters don't always agree. Most roasters link it to a rate of rise that stalls or crashes late in the roast. Cup side by side with a second taster before you change your profile.
No. A color reader measures average roast color, so a scorched or baked batch can still land on your target number. Use color readings alongside a visual check of whole beans and a cupping session.
A quaker is a pale bean that stays light while the rest of the batch browns. It comes from an unripe coffee cherry, so it is a green coffee defect rather than a roasting defect. Quakers stand out after roasting, and many roasters pick them out by hand before packing.
Usually not. Most defects on a newly installed roaster come from setup, cleanliness or a profile built for a different machine. Work through the machine checks, fix what you find, then fine-tune the profile. Persistent flame, drum or probe problems are a job for a qualified technician.
Leave a comment